How to Drill into Brick Without a Hammer Drill?

It may occur that you do not have a hammer drill to drill into brick. Bricks are solid and hard.

So, using an ordinary drill for this purpose would seem quite cumbersome. Do not worry because it is not a big deal.

Yes, if you do not have a hammer drill available for this job, then I will tell you how to drill into brick without a hammer drill. So, without any ado, let’s get right into it.

About Bricks

To develop a better concept in your mind, I want to convey it step-by-step. Like, you should know about bricks to decide on the right tools for this job.

So, a brick mainly comprises mud or sand processed to combine it firmly together. So, it’s kind of robust, and you have to go for a better plan to drill into it.

For that, most of the people go for the hammer drill. But we both know that we have not got that facility with us. So, we will need this list of equipment to support our different procedures.

Requisitions

Now, there is a list of stuff that you would need to carry out this process. So, if we are going with a different sort of procedure, then what’s that about.

Let me reveal that to you. It is also drilling but with masonry drill bits. Sounds strange? Grab the following list of equipment with you, and we will find out the exciting part. Trust me; it is possible to go with this process.

  • First things first, masonry drill bit
  • Working gloves
  • Safety goggles
  • Earplugs for protection
  • Mask
  • Measuring tape
  • Water
  • Wall anchor
  • Compressed air
  • Dusting brush

So, this is the general stuff that you would need. Don’t worry if you have some stuff unavailable in it. You should read through, and then you can improvise as well.

Safety Check!!

Alright, it’s not too far now. Just make sure about the following safety precautions, and then we are good to go for this ride.

So, the following are the precautions to make sure about:

  • Wear all the personal protective equipment before starting your project.
  • Never compromise on your safety and devise the safest technique to carry out the procedure.
  • Always keep in mind that your walls may have electrical wiring in them. So, make sure to trace them down before starting the procedure.
  • Beware of any concrete that can come in your way while drilling. Therefore, do not worry about them and keep doing your job.
  • If the surface is harder, you can take the help of a hammer and a large nail.

Step by Step Guide

Now the wait is over! Below is a comprehensive and step-by-step guide on how to get this job done. So, look closely and abide by the procedure for desired results. Here you go!

Step 1: Manage Your Masonry Drill Bits

A regular drill will not work as a hammer drill does. Therefore, you have to make sure about a lot of aspects. Just like that, you have to have several masonry bits with you, all in different sizes, to get your job done properly.

In this way, you can achieve smooth execution of the process. Remember that you will have to work with smaller masonry bits as you go up in the procedure. This will optimize the process for you. So, plan properly.

Step 2: Markings and Measurements

I call this step “Markings and Measurements.” However, the measurement is the first step to this step of the procedure. But it’s my way of rhyming it.

Now, you have to mark the points where you want to drill your holes for better accuracy; measurements matter. So, using your measuring tool, have a marker and note the point where you intend to do this job.

Once you obtain the markings, you are good to move on to the next procedure. Keep in mind that accuracy matters, and you have to follow the steps in an accurate manner.

Step 3: Make Things Ready

Make Things Ready refers to the beginning of this procedure. Now, you might be wondering about the “things.”

By this, I mean that you have to wear your protective equipment now because we are ready to deal with the instruments now.

You would have seen in the Requisitions section that I recommended a mask to wear while carrying this process out. It is better to have an N95 mask for this job. Because it is a respirator and it efficiently does the job.

Other than that, leather gloves are better. Use good earplugs to avoid the high dB of sound. Besides, safety goggles will protect your eyes from unwanted dust and flying pieces of debris.

Step 4: First Stage of Drilling

Here comes our first stage of drilling. This step is very crucial, and it would need your special attention.

Set your drill at low speed and place it perpendicular to the wall. Hold the pistol grip with one hand and use your other hand to hold the auxiliary handle.

Now, slowly start drilling. Do not drill at a different angle than perpendicular because that will lead to a bad alignment, and you will not get satisfactory results.

Don’t push too hard and keep drilling. A slow start keeps the drill from getting over-heated.

Step 5: Coolant Inclusion

A lot of people do not abide by this step while doing their practical projects. But coolant is necessary while doing jobs that generate heat.

Now, you might be wondering which coolant is I am talking about. It is basically water that I mentioned in the Requisitions.

The drill bit will get heated up by a very great extent, and watering regularly while working will do the job for you. It is good for a better outcome as well as the health of the drill bit.

Remember to apply water in the hole as well as on the drill bit. If the motor starts sputtering, immediately apply water to the drill bit.

Step 6: Take the Level Up

Now, what does that mean? Think about our main equipment here, that I demanded in a large quantity. Yes, the masonry drill bits. It is time to use the bigger ones now.

Once you have created a starter hole, it is time to use a bigger drill bit to increase the size of the hole gradually.

Make sure that you keep the angle perpendicular. Also, do not deviate from the parent hole because that can cause you problems.

The bolt that you want to insert defines the size of your hole. Now, you have to increase the size of the bit step-by-step to reach the desired diameter with technical tolerances kept in mind.

Step 7: Clear the Way

You know that while drilling, the debris will start to accumulate inside the hole.

Moreover, applying lubricant/coolant will make mud inside. Excess of that matter will come in the way of the drill bit to stop further drilling.

You have to control this situation, and you know the remedy as well. Yes, by removing the debris from the whole side-by-side.

Moreover, if some solid material comes in the way, it can be concrete or anything that is hard to penetrate.

For this, you have to hold the drill in the right posture firmly. Make the correct adjustments and apply constant pressure. You have to stay firm, and you will get through this.

Keep noted that forcing too hard will break the drill bit.

Step 8: Oscillations

Hereby oscillations, I mean that you have to follow a circle of the procedure. It is related to the operation of drilling.

When you are using a regular drill instead of a hammer drill, you have to regularly lift the drill bit out of the hole at intervals.

This is good for the health of the process. This process efficiently removes all the dust and unwanted stuff from the hole. Thus, you act properly against clogging up debris and excel efficiently in drilling the hole.

Step 9: Anchor in Place

Once you have your hole ready, it is time to place the anchor in. You might not have the idea of force analysis. Therefore, buy the anchor according to the weight that it has to support.

Do not worry because people in the market will recommend you a proper anchor having a good safety factor. Thus, you could safely hang your stuff with it.

Never compromise on the quality of anchor because you do not want to regret your decision later.

Step 10: Clear the Unwanted

Now is the part of the dusting brush. Working on a project in an organized manner tells a lot about you. Therefore, you have to give importance to the proper cleaning as well.

The brush can help you remove all the unwanted. But, if you want to elevate the level of cleaning, I would recommend you use a vacuum facility.

Before leaving the workspace, make sure that everything is clean and clear. Unplug all the tools and place them where they are usually organized.

Summary

Here is the summary of what we do to drill into brick without a hammer drill.

  • First off, we make sure about all the masonry drill bits and their availability.
  • Secondly, we perform the measurements and markings properly.
  • Next, we make sure about the personal protective equipment.
  • Now start drilling from small to larger bits to achieve the desired hole.
  • Properly drill the hard areas and do not go harsh.
  • Make sure to clear debris from the hole for better drilling.
  • Install the anchor properly by keeping the factors in mind.
  • Do the housekeeping before leaving the workspace.

Frequently Asked Questions

Here are some frequently asked questions to answer your general queries.

Can the Process of Drilling into Concrete Cause Cracks?

Well, it is understood that cracks occur in hard areas. Concrete is a very hard spot in the wall. If you do not drill properly, then it will cause cracks.

What’s the best speed for drilling into brick?

Going slow is better because the drill bit does not get hotter this way, and the process goes smoothly.

Can a Hammer Drill Be Used as a Regular Drill?

Well, why not! You have to turn the hammer mode off, and you can avail this feature from the hammer drill. So, you can confidently use it for regular drilling.

What else can You Use to Drill into Brick Besides a Hammer Drill?

You can go with a masonry drill bit and follow the entire process above, and you will be able to complete the process.

How to Drill into Concrete without a Hammer Drill (6 Useful Tips)

You will find ten useful steps above. So, why don’t you have a thorough view of the procedure? Read through the article above.

What do You Need to Drill into Concrete Without a Hammer Drill?

You can use tungsten carbide drill bits or masonry drill bits to undergo this procedure. Read the article above to find out a clear solution.

How to Drill and Screw into Concrete Without a Hammer Drill?

Well, first off, you need to drill a hole in the wall using a masonry drill bit with the proper procedure explained above. After that, you can anchor your screw in that whole as per your requirement.

How to Drill into Bricks with or without a Hammer Drill?

If you use a hammer drill, then the process is pretty simple and straightforward. Otherwise, you can go with the opposite procedure that I explained above.

Can You Drill into Concrete without a Hammer Drill?

Yes, you can do it effectively. You have to go slow and steadily to avoid any malfunctioning. You can follow the steps above to understand it.

Conclusion

I have tried my best to equip you with the necessary information and guidance that you should know for this procedure.

I recommend you follow all the steps properly for better results. Trust me, once you get used to it, t will become very easy for you. So, keep learning and exploring until you develop the proper understanding.

I wish you good luck in the process. Have a wonderful day!

Leave a Comment